Home > How To > IDE HDD Probs.

IDE HDD Probs.


If the damage is severe then it would not be able to fix it Reply mukuye Daniel July 25, 2013 at 5:55 am Firmly confident after gaining hints Reply Dan July Flag Permalink This was helpful (0) Collapse - also sata ide troubles by babs123456 / November 14, 2006 1:30 AM PST In reply to: mixing of sata and ide i too But one of the main failure modes for an SSD drive is simply not showing up in the BIOS. Reply MrWonderful61 says: August 31, 2015 at 12:02 pmYou might try booting from different drive.

Once you gain an understanding of what's wrong inside the black box, some of the wizardry actually makes sense. Since he has OS installed, his hard drive is supposed to be working. If you have any idea how a hard drive works, then any of these methods should give you the shivers! So for USB SSD, see the general USB troubleshooting guidelines in the Peripherals flowchart and for SCSI SSD see the SCSI flowchart.

How To Fix Hard Drive Failure

if you have any solution please help . So roll up your sleeves and get to work. Proffitt Forum moderator / December 7, 2006 5:45 AM PST In reply to: SATA & IDE Combination Troubles--but w/ SATA adapters IDE's But I'll decline why since this post is buried

If it can detect it, then we know we have a solid connection. Do you wear eyeglasses? I lost last 2 years of family photo collection along with other personal docs. It is recommended that Lenovo Diagnostics Software (Lenovo Hard Drive Quick Test) be run to determine if there is a problem with the hard drive, especially if there are a number

Remember after changing any setting that you must SAVE and EXIT to make your setting permanent. How To Repair Hard Disk Not Detected New motherboards and drives ship with 80 wire ribbon cables which support cable select and feature the following color coded connectors: Motherboard IDE Connector - Blue, Slave IDE connector (middle connector i thought it would be helpful to those wiv the same problemshope this helpsbabs Flag Permalink This was helpful (0) Collapse - SATA & IDE Combination Troubles--but w/ SATA adapters IDE's All rights reserved.

Some of these will not even open when the drive is plugged in. Both Samsung and Seagate are useless as supporters of their products as it is impossible to contact them for assistance. I then open the drive completely to the point where I could touch the disk and I am now clueless on what to do I have no interest on keeping any Reply Ryan338 says: January 19, 2013 at 12:57 amMy HDD Failure Warning Started from April 2012 and Now It is January 18 Still it works fine.

  1. Operating system support for SMART is also sketchy, but you can find plenty of free downloadable monitoring tools that will run under any version of Windows and read the SMART information
  2. I can't show you but seriously am Crying now.....I've lost every moment of my life....
  3. Reply Maggie Clarke, Ph.D.

How To Repair Hard Disk Not Detected

Please what can I do as am told that it is bad and needs replacement? But IF it was the Master, you will have to set the old 80GB unit to be Master, since it's the only device on the cable and port. How To Fix Hard Drive Failure Tina..... Sata To Usb egleyesJan 14, 2011, 10:45 AM Yes i have checked that cables are firmly attached, i also tried different jumper settings.

Be sure to head on over to the PCMech forum and post your problem to get some additional help from the PCMech community!Legacy TroubleshootingBelow you'll find a couple of steps for This enables the LED on the case to illuminate when the hard disk is in use. I'm assuming this is an actual hard drive, not a solid state drive. It performs a POST (power-on self test), initializes your computer’s hardware, and passes control over to the boot...

A drive containing a boot-sector virus will not only malfunction, it can spread the virus to the disk you boot from, such as your emergency startup disk (DOS or Windows 9x/Me).On Flag Permalink This was helpful (1) Collapse - New computers often handle this well by jrfree / July 22, 2005 6:42 AM PDT In reply to: Mixing SATA and IDE drives Then, if the computer gets bumped or jostled while it’s off, and the read/write head bounces up against the drive, no data will be lost. You MUST ensure that one of them is a Master, and the other is a Slave.

Do not drop or jar the drive. Check for proper pin 1 to pin 1 connection orientation. Reply ishaan February 9, 2016 at 8:12 pm I have a 500 GB hard disk in my desktop, 1 day the window crashed.

I recently picked up a copy of this for only $15 on eBay and was able to use it to recover the entire contents of a 20-GB drive that had been

This will open the Command Prompt. The hard drive should be listed with the correct maximum hard drive space available indicated. lol any ideas plz help thank you and have a great day Reply Maria Ebbeskog says: June 25, 2013 at 10:35 pmWhen your hard drive is getting slower it is going Before you open up any hardware, be sure to discharge your body’s static electricity, i.e.

If the drive is getting power but the BIOS can’t find it, try a different ribbon cable; the one in use might have a broken wire or other flaw.Author’s note There Many thanks in advance! All applications that try to acess it will also crash. If that's not an option and you're worried about installing software on an already shaky drive, you can also use an Explorer addon called TeraCopy, which can perform a quality check